李剑峰山东大学主页平台管理系统--中文主页

李剑峰

学位：工学博士学位
职称：教授
所在单位：工程训练中心

教师英文名称：Li Jianfeng
教师拼音名称：Li Jianfeng
出生日期：1963-01-21
入职时间：1985-07-01
所在单位：工程训练中心
学历：博士研究生毕业
办公地点：1.兴隆山校区工程训练中心 2.千佛山校区创新大厦814
性别：男
联系方式：13954168841 ljf@sdu.edu.cn
在职信息：在职
毕业院校：山东工业大学（山东大学）
是否在职：1
博士生导师
硕士生导师

论文成果

[91] 满佳. Intravenous Calcium Alginate Microspheres as Drug Delivery Vehicles in Acute Kidney Injury Treatment. MICROMACHINES, 13, 2022.
[92] 任远. The Surface Properties of an Aviation Aluminum Alloy after Laser Cleaning. COATINGS, 12, 2022.
[93] 王鹏飞. Effects of microstructure and inclusions on very high cycle fatigue properties of compressor blade steels. Strength Fract. Complex., 10, 1, 2017.
[94] 周晨晨. Fabrication of weaved ceramic mesh from green microfibers based on cross-flow microfluidics. Journal of the European Ceramic Society, 41, 7744, 2021.
[95] 张松. Effects of constitutive model parameters on finite element simulation process for hard milling of AISI H13 steel. 2021.
[96] 许亚鹏. A Novel Rotational Actuator With Variable Stiffness Using S-Shaped Springs. 《IEEE-ASME TRANSACTIONS ON MECHATRONICS》, 26, 2249, 2021.
[97] 孙福来. Accurate measurement of CTE of aluminum alloy 7050-T7451 and the impact on thermal deformation analysi. Advanced Materials research, 566, 476, 2012.
[98] 周军. Finite Element Analysis of Micro-Cutting Aluminum 7050-T7451 with the Tool Edge Radius Considered. Advanced Materials research, 2010.
[99] 王福增. Experiments and finite element simulations on micro-milling of aluminum alloy7050-T7451. Advanced Materials research, 500, 650, 2012.
[100] 苑荣华. Experimental Study on Surface Roughness and Residual Stress by End Milling 69111 Stainless Stell. Advanced Materials research, 97-101, 1257, 2010.
[101] 苑荣华. 69111铣削加工参数优化研究. 《工具技术》, 43, 18, 2009.
[102] 黄晓明. 7050--T7451铝合金预拉伸板材热膨胀系数变化规律及机理. 《中国有色金属学报》, 23, 3282, 2013.
[103] 孙杰. Effect of initial residual stress and machining-induced residual stress on the deformation of aluminium alloy plate. SV-Journal of Mechanical Engineering, 2015.
[104] 朱兆聚. Investigation on the influence of tool wear upon chip morphology in end milling titanium alloy Ti6Al4V. international Journal of Advanced Manufacturing Technology, 2016.
[105] 孙玉晶. 钛合金铣削加工刀具磨损有限元预测分析. 机械工程学报, 2016.

共505条 7/34

首页上页下页尾页页

扫一扫用手机查看